piotres' suction lines, "fix evapo" ;-P

Hello

In ACTION :

Ultramarine casade made by me, and 2 GPU suction lines which I've showed above attached to two Prommies (no, I haven't modded those prommies : ) .









Thanks for pics Musicismylife .

Best Regards
Peter

Nice. What were the temps ?

I don't have any info about temperatures on those modded prommies .

http://www.benchbrothers.de/forum/thread.php?threadid=9&sid=

-35°c for the best mach2 and -15°c for the second in full load. (problème de charge ils racontent...)

nice succion lines piotres

Hi

One more set for phase-change enthusiast .

GPU plus CPU suction lines
braided flex hoses DN10 100 cm long
0.9mm captube
18 mm thick insulation
Kprobes
red sleeve




















Packing work .

On photo there is lack of GPU backplate becasue backplates have been powder coated that day . But kit has also Stainless powder coated backplate GPU .

GPU evap is fitted for all cards, included 2900XT, 3870X2 and 9800 GTX .

Thanks
Best Regards
Peter

Hello

Latest suction line - for small SS which I sent together with NL11F compressor - "Young phase-changer kit" .

Braided suction hose, 18mm thick insulation, Kprobe ...

















Best Regards,
Peter

Hello

I want to show You three suction lines - the latest I've made :

Two suction lines in black sleeve have 100 cm of DN10 flex hose, CPU enclosure which fits all CPUs included last nehalem cores, 18 mm thick insulation, K probe on each one , captube 0.9mm .

Red suction line is an old suction line which I remake - it's from triple-evap unit which I must diseamble (becasue I couldn't sell it ;-/) . It was sth like 110 cm long flex hose but I braze suction flex hose again on both sides so now suction flex hose have 104 cm , insulation is new 18mm with red sleeve (was 13mm with black sleeve), captube is also new 0.9mm, I've mount also new Kprobe on evaporator .















And the red one :



Old CPU suction line together with GPU line...





I must scrap whole insulation from old suction line , and some cooper I also decide to throw away ...

New captube I use 350cm of 0.9mm but more than 100 cm is not wrapped around suction flex, so owner can cut it easily if he'll decide that's too long .










Regards
Peter

Nice work

Right. I've changed that sh*tty one I've got from someone else and replaced it with one of those by Piotres. That was a good move.

Another one :

Lenght of flex hose : 100 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : steeper 42mm diam/41 mm tall
Insulation : 18 mm thick + suction line sleeve black









Regards
Peter

Another one made today, GPU type, using OLD GPU suction line, evap is old revision, line today was brazed once again, pressure checkeck in water, and applied fresh insulation .

Lenght of flex hose : 100 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : steeper type GPU, old revision
Insulation : 18 mm thick + suction line sleeve black











Regards
Peter

3 new :

1)
Lenght of flex hose : 128 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : steeper type CPU, 42mm diameter, 41mm tall
Insulation : 18 mm thick + suction line sleeve blue







-------------
2)
Lenght of flex hose : 100 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : steeper type CPU, 42mm diameter, 41mm tall
Insulation : 18 mm thick + suction line sleeve black









-------------
3)
Lenght of flex hose : 75 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : steeper type CPU, 42mm diameter, 41mm tall
Insulation : 18 mm thick + suction line sleeve black with small white stripe

To this suction line I've also add some 15/9 and 35/9 armaflex insulations to insulate rest of unit - suction line will be working with NL11F compressor .













Regards
Peter

2 almost same suction lines - difference is only captube lenght . I must say that 100cm lenght and black sleeve seems to be "standart" suction line .


Lenght of flex hose : 100 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : steeper type CPU, 42mm diameter, 41mm tall
Insulation : 18 mm thick + suction line sleeve black













Thanks for looking

Best Regards
Peter

If someone want I can only braze flex hose :

Lenght of flex hose : 100 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : -
Insulation : -

BTW every of mine suction lines are tested under 25 bara pressure in water bath .








One made for another polish builder :

Lenght of flex hose : 100 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : steeper type CPU, 42mm diameter, 41mm tall
Insulation : 18 mm thick + suction line sleeve black with white stripe (chilly1 style ) .











Best Regards
Peter

Nice job
I'm interested in your last succion line (last picture )...What Price for it ?
THX

Thx ! YGPM

3 new suction lines ... and new polishing quality (using machine)

1. Lenght of flex hose : 100 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : steeper type CPU, 42mm diameter, 41mm tall
Insulation : 18 mm thick + suction line sleeve blue










2. Lenght of flex hose : 80 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : steeper type CPU, 42mm diameter, 41mm tall
Insulation : 18 mm thick + suction line sleeve black






3. Lenght of flex hose : 86 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : steeper type CPU, 42mm diameter, 41mm tall
Insulation : WITHOUT insulation

And that's new polishing technique










With Best Christmas Wishes,
Peter

Hello

Last time I've a request to make only two brazed evaps . With 0.9mm 300cm captube brazed, all cleaned and pressure tested .

That's how one kit has looked :














Thanks for looking.
Best Regards,
Peter

Hi

GPU suction line & new 54mm steeper evaporator brazed :

1. Lenght of flex hose : 120 cm
Flex hose type : braided stainless DN10 (10 mm Inside diameter)
Evaporator : steeper type GPU, 42mm diameter, 20mm tall
Insulation : 18 mm thick (2 layers total) + suction line sleeve black















2. 54mm diameter/43mm tall steeper evaporator - mass is more than 65% higher than 42mm diameter evaporator :eek:.

Compared to 42mm:













Thanks
Regards
Peter

It's shining so much, I need my sun glasses

Very good job, I'm always amazed by the polishing of your evap'

Hi

Twins with big 54mm evaps

New is also 19mm thick 1-layer insulation (till now I've used 2x9mm=18mm).










Thanks for looking !
Regards
Peter

Hi

Another one with 54mm evaporator (the BIG one), green sleeve, 19mm thick insulation and K-probe. Went to Germany .







Thanks
With best Christmas wishes
Peter

Hi Piotres !
What do you do to have such shining polishing ?

Well....I polish them .

I use foam pad mounted to driller, and autosol compound .