Cooling-Masters
Connexion · INSCRIPTION · Site Recevoir à nouveau l'e-mail de validation


[vds]ROTARY 10K+ BTU :LG 185PAD - 2 pcs and some other

Ajouter ou retirer ce sujet de vos favoris  ·  Suivre ce sujet  ·  Imprimer ce sujet
Page précédente    Page suivante 
piotres


Membre
Messages : 369

samedi 10 janvier 2009 à 23:31:27     
Hi

SORRY ENGLISH language contact only ..

First of all sorry that photos have that on photos You can see that stupid piece of paper with "piotres@xs" I make advertisement also on xs forum and there it's must, I only have one version of photos.

ROTARIES: All mentioned above are new, never used, only were mounted once in aircon units, which never came to shops (cases of A/C units was damaged in transport) , ALL are complete with rubber legs , cables and start capacitor . I'm not sure of exact power, mentioned BTUs are only mine shoot, based on varoius infos found in internet .


SHIPPING WORLDWIDE, please ask me about shipping price to Your country .






LG 185PAD (LRA 21) - over 10000 BTU - have 2 pcs for sale - 120 eur/one, 210 eur for two

and





Waterchiller with rotary compressor - I want to sell this whole chiller unit but this is not working well only becasue of HX with too little pipes diameter - it's making lower than -20C unloaded but water can't flow via HX without restrictions. It's one of mine first builds . Now I don't have time to test it again (maybe during holidays ...if it won't be sell before hehe).

It's leak free, filled with R507. Condensor around 1.5 kW and fan 230V are used, painted, gauge is REFCO, it has Kprobe on end of HX. ROTARY compressor in this one is sanyo remark 6826 BTU - price only for compressor from this unit = 80 eur .Price 120 eur for whole chiller like showed on picture ! If anybody wants - I can mod this to plate HX, fill with R507 and that will be fully working chiller making around -10-15C liquid with HUGE load around 500w.


------------------






Suction lines from this unit (was working sth like 50 hours total) : http://www.xtremesystems.org/forums/showthread.php?t=142426

So CPU plus GPU evaps (GPU evap have flat bottom so won't work on cards where core is lower than IHS so 2900xt for example) (I'll give enclosures - for CPU and for GPU too , bolts, insulation for evaps etc) + 13mm thick insulation + sleeve + Kprobes x2 + captubes+ braided DN10 hoses inside sth like 110 cm long each one, all pressure tested - price 120 eur for all ! Or 90 eur for CPU line and 40 eur for GPU line .





ALCO steel filters/driers- for sale all 3 together like on picutres,two for 3/8' flare pipe and one for 3/8' brazed, pipes comming out of driers were closed by factory= price 20 eur/ for 3 driers like on picture.

CONTACT : (please ask me about shipping costs to Your country)

Emails :

-piotrek_wis@poczta.onet.pl

or

-builtbypiotres@op.pl

-PM on this forum

- MSN : piotrek_wis@poczta.onet.pl



Thanks
Best Regards
Peter
Google




     
piotres


Membre
Messages : 369

mardi 27 janvier 2009 à 02:52:38     
bump
piotres


Membre
Messages : 369

vendredi 30 janvier 2009 à 23:03:20     
CPU suction line = SOLD !

Left GPU suction line from photo above (description there too), cost 40 eur

I have one more thing for sale :







Brand new, boxed, Danfoss KP15 dual cut-off (low and hi side), with manual reset . Just like from shop . Cost 94 eur in Kaeltetechnik-Shop. I want 55 eur for it .

Regards
Peter
piotres


Membre
Messages : 369

mardi 10 février 2009 à 18:27:44     
To Moderators : Please remove this topic .
Google




     
Page précédente    Page suivante